With the growing popularity of the plastic recycling industry, the application of the plastic granulator machine (also known as the plastic pelletizing machine) is increasing rapidly. During daily use, waste plastic pelletizer machine users may encounter some glitches. This requires timely analysis of the cause and troubleshooting. Here is an explanation of its common faults and solutions.

Краткое введение в машину для гранулирования пластика

Оборудование для гранулирования пластика также называется машиной для гранулирования отходов пластика. Будучи самым важным оборудованием в линии переработки пластиковых пленок, оно часто используется на заводах по переработке пластика. Пластиковый гранулятор обладает такими характеристиками, как энергосбережение, высокая эффективность, стабильная работа, простота в эксплуатации и обслуживании.

пластиковая грануляторная машина
пластиковая грануляторная машина

5 распространенных неисправностей и методы их устранения

Ниже приведены общие проблемы и соответствующие решения для машины по производству пластиковых гранул. Надеемся, что информация ниже будет полезна вам при использовании машины для производства пластиковых гранул.

1. Главный мотор гранулятора пластика не вращается или мгновенно отключается

  • Reasons: unstable power supply voltage or poor contact; insufficient heater heating or a heater does not work, which makes the motor overload due to excessive torque
  • Treatment methods: check the main motor circuit connection of the plastic granulator machine; check the temperature display of each section of the heater, and check whether the heater has poor contact or damage.

2. Главный мотор машины для производства гранул вращается, но шнек не вращается.

  • Causes: The transmission V belt becomes loose, wears and slips; or the safety key becomes loose or disconnected.
  • Troubleshooting methods: adjust the center distance of the V-belt, tighten the belt, or replace with a new V-belt; check the safety key, analyze the cause of the break, and replace the safety key.

3. Шнек гранулятора работает нормально, но не выгружает материалы

  • Reasons: the feeding of the hopper is not continuous; or there is a foreign object blocking the feeding port; or a metal hard object falls into the screw groove to block the screw groove, and the material cannot be fed normally.
  • Solutions: The troubleshooting method of this failure: increase the feed volume to keep the screw feeding continuously; stop the machine to check and remove the foreign matter in the feed port. If it is confirmed that there is a metal foreign body falling into the screw groove, stop the machine immediately to remove the screw and remove the metal foreign body.

4. Машина гранулятора пластика вызывает выход материала из вентиляционного отверстия

  • Causes: there are impurities in the raw materials, or the feed speed is too fast to make the screw extrusion unstable, or the plasticization temperature is not enough.
  • Treatment method: clean the raw materials before feeding or replace the filter screen, or reduce the feeding amount to make the screw extrude smoothly, or increase the plasticizing temperature. However, the temperature should not be too high to prevent burns to the plastic and affect the quality of production.

5. Основной крутящий момент двигателя слишком низкий

  • Reasons: the feed system failure caused the twin-screw idling.
  • Solution measures: Check whether the additive system or the main material feeding system is faulty, and clean the blockage of the plastic granulator.

В заключение, необходимо своевременно провести анализ неисправностей и принять разумные меры, чтобы обеспечить нормальную работу машины для гранулирования пластика.